EU? SH-HC31 24V Plasma Flame Cutting Machine Arc Voltage Torch Height Controller

SH-HC31 24V Plasma Flame Cutting Machine Arc Voltage Torch Height Controller. A ustria, B elgium, B ulgaria, C zechRepublic, D enmark, E stonia, F inland, F rance, G ermany, G reece. H ungary, I reland, I taly, L atvia, L iechtenstein, L ithuania, L uxembourg, M onaco, N etherlands, P oland. P ortugal, R omania, S lovakia, S lovenia, S pain, S weden, UK. 100% Brand New and High Quality!!

Model SH-HC31 height controller for flame/plasma cutting torch is simple and easy to use, convenient to commission and modest in price. In addition, it insists the sell points of all Microstep products--good product performance at modest price. It is an ideal accessory to match welding or cutting equipment. Processor: Industrial grade ARM processing chip. Automatic Height Control Range: 2-30 mm.

Speed to Automatically Control Height: 3000 mm/min (30° slope). Housing Size: 410 x310 x58mm.

Operating Temperature: 0 to 40 deg. Storage Temperature: -40 deg to 60 deg.

Applicable Motor: 17/23 HS series of stepper motors. Please read and strictly comply with the following instructions before operating the product, thus to assure the designed product control accuracy and prevent any damage and accident. Installation must be carried out by certified technical personnel with relevant experiences. Please thoroughly read the instructions before starting installation.

Make sure the local power supply satisfies the required specifications. Installation, plugging or unplugging power cord are prohibited when the power switch is on. The product should be positioned far away from any heat source if possible. The controller shell must be grounded well to avoid electric shock or affecting the controller. The work piece must be well grounded too and maintain a good connection with the controller shell for assured accuracy of height control. Note: If the controller shell and the work piece are not properly grounded, the height controller will not work normally. Please handle the product with care and make sure no impact or shock; otherwise, damage to the product might be incurred.

Never try to disassemble the product or modify its internal construction. Otherwise, accident or fault might occur.

One-keystroke height calibration: In capacitance height measurement mode, the specific inductive capacity between the capacitance detection ring and work piece may affect the accuracy of height. Measurement due to temperature, pressure, humidity, gas composition and many other ambient factors.

In addition, the serious non-linear relationship exists between capacitance value and height value. Microstep has developed the intelligent program of "one-keystroke height calibration". Only one keystoke will automatically set the product based on various ambient factors. And within the range of. 2-30mm, high accuracy, high precision and high linearity is possible in display and control.

High speed zone: When the difference between the actual height and the set height is relatively big, the cutting head will advance towards the set value at the highest speed in order to reach the set value the soonest; this travel zone is called high speed zone. Intime, butoscillation may be caused. Speed regulating zone: If the cutting head reaches the set value at a high speed, severe oscillation may be caused and the height control is unstable.

In order to achieve a smooth transition, the speed regulating zone is set. This zone is located between the high-speed zone and the dead zone. In this zone, when it is far away from the set value, thecutting head will move at a higher speed; otherwise, at a lower speed. The range value of this zone is adjustable. If it is set too big, the transition is smooth, but the tracking time is too long; if it is set too small, the tracking is conducted in time, but oscillation may be caused easy.

Dead zone: Within a certain height range, the height of the cutting head will not be adjustable any more. The range is called dead zone. The dead-zone range is set too wide, the control precision will be too. Low; if it is set too narrow, the cutting head may oscillate up and down easily. An appropriate value of dead zone will not only guarantee the control precision but also generate no oscillation.

Height & Sensitivity Adjustment Knobs: With height and sensitivity knobs, it can adjust the height and sensitivity statically or dynamically, and the setting result can be saved in real time. It is quite convenient to use. Featuring longer life span and reliability, the pulse adjustment knob exceeds the contact potentiometer. Industrial-grade ARM Processor: The HC31's processor has been upgraded from a microcontroller to a new ARM.

Its processing speed is greatly improved, featuring a more powerful lifting speed algorithm, faster dynamic response, and improve anti-interference ability. Stepper Motor Drive: The built-in stepper motor driver of HC31 can set the drive current through the controller, and has more than 3 times of overload current. The reliability and impact resistance are far beyond the simple drive chip.

Aluminum Alloy Structure: Made of high quality aluminum alloy, its mechanical strength and performance are much better than others with sand-casting shell. Problem&Feedback Please give us the opportunity to resolve any problem when you have, we concern your problem and we will try our best to resolve it. Item must be in it's original condition and no physical damage. This item is in the category "Business, Office & Industrial\Industrial Automation & Motion Controls\Other Automation Equipment".

The seller is "powace08" and is located in this country: DE. This item can be shipped to United Kingdom, European Union.

Modified Item: No
Country/Region of Manufacture: China
Custom Bundle: No
Automatic adjusting range: 3-30mm
Power Requirements: DC 24V ±2V 3A
Application: Plasma cutting machines and plasma cutters
Communication interface: RS232
work temperature: -10 deg - 50 deg
Applicable motor: 17/23 HS series of stepper motors
Manual adjusting range: 0-100mm
Model Number: SH-HC31
Control accuracy: ±0.5 mm
Brand: RATTM MOTOR