Plasma Cutter Machine

Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine


Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine

Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine    Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine
ADJUST HEIGHT: HP105 can continuously adjust the height of the cutting torch on the uneven steel plate according to the set arc pressure value, so as to ensure that the height of the cutting torch to the steel plate remains constant 2. IMPROVE EFFICIENCY: Automatic control of cutting distance enables you to obtain kerfs, reduce workpiece scrap, and improve cutting speed and efficiency 3. MOTOR CONTROL: When HP105 is working in automatic or manual state, the lift switch on the panel can be operated to control the lift of the motor 4. AUTOMATIC CONTROL: When switching to automatic mode and there is input arc voltage, the controller controls the cutting height according to the arc voltage setting value on the HP105 panel 5. WITH FITTINGS: Equipped with screws, nuts, fittings, easy for you to install, complete accessories guarantees convenient operation. Item Type: Torch Height Controller Material: Aluminum alloy Dimension: Width: Approx. 225mm / 8.86in Height: Approx. 80mm / 3.15in Depth: Approx. 49mm / 1.93in Input: DC 24V±10%, 2A Lifting Motor: DC24V permanent magnet DC motor Output: DC 24V Maximum 40W Speed Control: Dual Pulse Width Modulation (PWM) with electric drive voltage feedback Arc Voltage Range: 30-250V Arc Voltage Accuracy: 1V-5V, which can be adjusted by parameters Initial Positioning: 1.

Proximity switch initial positioning 2. Contact initial positioning(need to support isolation positioning box) Input Arc Voltage: 1: 1 or 50: 1 arc voltage value(built in isolation voltage divider) Working Environment: -10? Host Weight: 0.8 kg / 1.8 lbapprox. Protection Class: IP64, prevent dust from entering Mounting Connector: 2 pin, 4 pin, 5 pin, DB 9 pin Installation Location: Away from heat sources, a place with good convection. The built in isolation voltage divider of the controller defaults to input the actual arc voltage of 1:1.

For some plasmas that come with a 50:1 non isolated divider, the input can be set to 50:1. Do not connect the actual arc voltage wire directly to the ground clip and torch cable. The cable from the arc voltage height controller to the motor should be shielded cable, and the shielded should be connected to the ground of the machine. The power supply and arc voltage height controller must be strictly grounded.

Be careful to check the torch height and grounding clamp before starting the arc. Domestic Power Supply: Arc voltage must be taken from the high frequency arc ignition stage and before the reactor. Sampled from the position of the rectified output of the. Any control cable and torch cable should be kept as far away as possible (above 5cm) when wiring to prevent high frequency coupling into the control signal and damage to the controller and numerical control system.

We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better.

We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders. This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\Plasma Cutters".

The seller is "fungee33" and is located in this country: CN. This item can be shipped worldwide.

  1. Brand: Unbranded
  2. UPC: 691096452523
  3. EAN: 7051486953833


Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine    Digital Cutter Torch Height Controller HP105 Arc Voltage Cutting Machine