Customizable coordinate system, supporting all eight possibilities for two-dimensional coordinates. Customizable all input and output port types (normally open or normally closed) and numbered.Self-diagnosis of all IO status and button status of the system for easy inspection and troubleshooting. Front USB interface for easy program transfer. The system upgrade adopts the U disk upgrade mode, which is convenient, simple and practical, and provides life upgrade service. Support system backup and system restore function, system restore can restore only the operating system, can also be restored to the factory state. All functions and processes of the entire system can be upgraded online, eliminating the worry of after-sales.
Import and export processing files individually or all. Parameter backup and parameter restoration. Supports 4 modes of oxygen gas, plasma, dusting and demonstration. Various processing parameters are available to meet different process requirements. Oxygen gas and plasma IO are controlled separately.Oxygen gas is automatically adjusted, two-stage preheating, three-stage perforation. Plasma arc pressure feedback, positioning feedback, automatic closing of the arc voltage. Built-in plasma arc pressure automatic / manual height adjustment function: can display the actual arc voltage and set the arc voltage, set the arc voltage. Increase parameters, detect collision/positioning success signal, arcing signal control, positioning test.
Plasma arc pressure control supports both speed and distance to close the arc voltage height adjustment mode, making the machine tool more stable. Support edge cutting, reduce warm-up time for thicker steel plates.
Accelerate and decelerate in real time during exercise. According to the thickness of the steel plate, the speed limit can be automatically set at the corner to effectively prevent overburning.
Manually select the starting line or select the perforation point. Dynamic/static processing graphic display, graphic enlargement/reduction, dynamic tracking cutting point in zoomed state. DSP high-speed, high-precision interpolation control, high-speed operation, stable operation, low noise.
Arbitrarily set the starting speed, lifting speed time. With power-off, breakpoint protection memory function.
Offset cutting function avoids sheet waste due to incorrect counting calculations. Different management rights and corresponding passwords can be set to maintain the rights of equipment manufacturers. Remote control that supports P2P mode or BCD (8421) mode. Item Type: Plasma Cutting Machine Control System Number of Control Axes.
Maximum Pulse Frequency: 200KHz; maximum operating speed: 15 meters / minute Maximum Number of Program Lines. System Working Power: DC +24V DC power input, power is greater than 80W.10 ° C to +60 ° C. Relative humidity 0-95% without condensation Drive Arc Voltage Increase Motor Maximum Power.
(Note: only with T system) System Interface: 15-core male two-axis motor drive interface 16-core female 16-channel opto-isolated output, maximum sink current 300mA 25-core male 16-channel opto-isolated input, maximum input current 300mA The front panel has a built-in USB interface for the user to transfer the cutting code Extended IO input and output port; PWM input port; analog input port The following interfaces, the F2000 series CNC system with "T" are available: f Arc voltage input divider ratio selection can be selected 1:50 or 1:100 5-core arc voltage boost motor output and limit input 7-core arc voltage and positioning input, arcing signal output port Environmental Requirements: The numerical control system is suitable for working at an ambient temperature of 0 ° C to 50 ° C, and a relative humidity of 5-95% without condensation. The working voltage is DC +24V.This controller should be installed in a console enclosure with protective dust. This system is best used in places away from high-voltage high-frequency and high-radiation. When using, do not splash acidic, alkaline, corrosive and other items on the control system. Instead of leaving negative/neutral feedback or opening a dispute. Our listing price includes the value of goods, packaging cost, and export. Please check with your country's.
We will reply your message within 48 hours. If you do not receive our reply within 48 hours, pls. Post a message again because sometimes our message system may block some emails. If you are satisfied with our service, pls. Our aim is to provide Level Customer Service, your recognition will encourage us greatly and serve you better.
We strive to keep all our customers satisfy. We will do our up most to exceed your expectations in customer service, communication and dispatching of your orders. The item "CNC Cutting Machine System Control System Multifunction Precise Simple Industry" is in sale since Friday, December 11, 2020.This item is in the category "Business, Office & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\Plasma Cutters". The seller is "nicedeal-de" and is located in Shenzhen. This item can be shipped worldwide.